Wire size for 10 A over 200 ft on a 48 V system

Smallest wire that works

4 AWGat 2.57% drop

10 A over 200 ft one-way on a 48 V system

Circuit power10 A × 48 V	480W
Conductor length200 ft out and 200 ft back	400ft
Ampacity alone would allow26.17% drop — legal on heat, not acceptable on drop	14 AWG
Power lost in the cable2.57% of what you are sending	12.3W
— Voltage drop by size —
14 AWG15 A rated, drop too high	26.17%12.56 V
12 AWG20 A rated, drop too high	16.5%7.92 V
10 AWG30 A rated, drop too high	10.33%4.96 V
8 AWG50 A rated, drop too high	6.48%3.11 V
6 AWG65 A rated, drop too high	4.09%1.96 V
4 AWG85 A rated	2.57%1.23 V
2 AWG115 A rated	1.62%0.78 V
1/0 AWG150 A rated	1.02%0.49 V
2/0 AWG175 A rated	0.81%0.39 V
4/0 AWG230 A rated	0.51%0.24 V

Current: 10 A
One-way distance: 200 ft
System voltage: 48 V

Ampacity and voltage drop are two different questions

Ampacity asks whether the wire gets hot enough to be dangerous. Voltage drop asks whether enough of the power arrives at the other end. On a low-voltage DC run they almost never give the same answer, and the bigger one wins.

For 10 A over 200 ft at 48 V, ampacity alone would allow 14 AWG. Voltage drop says 4 AWG — 2.57%, or 1.23 V of the 48 V you started with.

Why the distance doubles

Current goes out on one conductor and comes back on the other. The copper in the circuit is 400 ft, not 200 ft. Forgetting the return leg is how people arrive at exactly half the real drop.

Why it matters more than it sounds

480 W leaves the source. Undersized cable does not just waste a few percent — on a solar charge controller it means the battery never sees absorption voltage, never finishes a charge cycle, and sulphates its way to an early death while every meter in the system reads normal.

What is not in the table

Copper at 75 °C. Aluminium conducts about 60% as well — go up two sizes. Conduit fill, ambient temperature above 30 °C and bundled conductors all derate ampacity further.

Notes

Two different answers, and the bigger one wins. 14 AWG carries 10 A without overheating, but it drops 26.17% over this distance. You need 4 AWG — sized by voltage drop, not by heat.
3% is the NEC informational recommendation for a branch circuit, not a hard rule. On a 48 V DC system it is already generous: 1.44 V of the 48 V you started with.
Running at 48 V is doing a lot of work here. The same 480 W at 12 V would draw 40 A and need a far heavier cable.
Figures are copper at 75 °C. Aluminium runs about 60% of copper conductivity — go up two sizes. Conduit fill, ambient temperature above 30 °C and bundling all derate ampacity further, and none of that is in this table.

Nearby sizes

Roof Space for a 10 kW Array: Panel Area Is Not Roof AreaTwenty-five panels cover about 525 square feet. The roof they need is closer to 680, and the gap is mostly required by code rather than by geometry.
Daily Solar Output by Region, and the Seasonal Swing Behind the AverageAn annual average tells you what the system produces over a year. It tells you almost nothing about December, and December is where the sizing arguments happen.
How Many Panels for 1,000 kWh a MonthThe answer ranges from fifteen panels to thirty-four, for the same house using the same electricity. Location does most of that, panel wattage does the rest.
Converting kW to Panels, and the Three Ratings That Get ConfusedThree different numbers on a solar quote are all measured in kilowatts and none of them mean the same thing. Knowing which is which makes quotes comparable.